Harley transmission shift lever how to#
Harley transmission shift lever upgrade#

I can rest my boot heal against the shifter and the chattering sound stops. When idling, the heal/toe shifter puts out a lot of chatter. Shifter Chatter РІР‚вЂњ 2008 FLHTCU РІР‚вЂњ 48,022 miles Never mind I watched it again and see the the screw is inside the case. i saw the video on tightening if with an allen wrench but need to know if that can be done without removing the primary case. What is the year and model of your motorcycle? Reply We would be happy to assist you we just need some more information. Customer Service Techs November 18th, 2015.Greener then Lettuce at this but have learned so much from the videos.

Shifting from 1st to 2nd gets stuck in РІР‚СљNРІР‚Сњ need to clutch again to get past this.

Harley transmission shift lever upgrade#

Depending one what you ride, check out the Rear Belt R&R Videos, the Transmission Class Videos and the clutch upgrade videos for Sportsters. I need to remove the midshift lever, and plug the primary. It seems as though something is out of sync. I have torn the bike down to the top cover and peeked inside.The pawl arm reaches to 3rd gear, but it stops cold. However, when in 1st, the toe shift is so low I can barely get my foot underneath it. Hope every is well with all of youРІР‚В¦ IРІР‚в„ўm having trouble with my bike shifting into the 3rd, 4th, 5th and 6th gear. I have replaced the pop metal shift arm 2 times then I got after market steel one have had no more problems HD told me would need to replace shaft the pop metal can not hurt the steel shaft Reply

It does work loose so in the reinstall I used the removable medium lock tite Reply I then could tighten the allen perfectly. Taking it easy and going in a little and then out to clear the metals. I took a tap of the same pitch and ran it through the threads a couple of times. Hi Michael, you should be able to disconnect the clutch cable at the transmission. Hi,i have a 1986 fxstc,how to replace clutch s not like newer,it comes in top of tranny on left side Reply It makes me crazy and harder to shift I am sure. I am wondering and hoping that I can do that shift pawl adjustment and lose the slack. And I recently pulled the inner primary off and replaced the aft shift arm which by the way was shot. it should squeeze the arm enough to eliminate the slop. If its the shifter arm coming off the transmission more then likely the arm is worn and needs replacingРІР‚В¦.IРІР‚в„ўve replaced 2 arms on my baggers over the years and YES I checked the allen bolt and both times it was tightРІР‚В¦Unfortunately the inner primary has to be removedРІР‚В¦.After the second one I while it was apart I replaced the cheap allen bolt with a longer bolt,washers and locked nut with nylon on the theadsРІР‚В¦.t ReplyР”В«ack the allen screw off, get some lube on it, then tighten it. ItРІР‚в„ўs a Twin Cam but will be similar Reply HI Michael, We have a video class on a transmission project.

Harley transmission shift lever how to#

I donРІР‚в„ўt know where to ask this question please help? I have a older 1986 fxstc,where can I find instructions on how to replace forks in my tranny? Reply Hi Steve, Sounds like that seal is an issue.

Dennis Santopietro September 24th, 2014.

What should I do to stop the leak ? Reply I let it set for 48 hours before starting the engine. I removed the plug and reapplied loctite. Now I have leak from the primary case were itsРІР‚в„ўs pluged from the former mid control shifting location.

I installed forward controls about one year ago. Articles on Harley-Davidson How-to and More